Determination of Chilling Requirement of Arkansas Thornless Blackberry Cultivars

Little research has been done to determine the chilling requirement for blackberry cultivars. However, field observations from areas where fewer hours of chilling occur indicate that ‘Navaho’ requires more hours of chilling than does ‘Arapaho’. The objective of our study was to determine a method for measuring the chilling requirement using whole plants of two blackberry cultivars, Arapaho and Navaho. One-year old, bare-root plants were field-dug on 26 October 1999 and placed in a cold chamber at 3ºC. Ten single-plant replications of each cultivar were removed at 100-hour intervals up to 1000 hours. The plants were potted and placed in a greenhouse (daily minimum temperature 15ºC), and plants were arranged on benches in a completely randomized design. Budbreak was recorded on a weekly basis. Data for budbreak were analyzed as a two-factor factorial (2 cultivars and 10 chilling treatments) by SAS and means were separated by least significant difference (P = 0.05). Data indicated that the chilling requirement for Arapaho is between 400 and 500 hours. For Navaho, the data indicated the chilling requirement was between 800 and 900 hours. These data support previous observations and indicate that the method used was successful in determining the chilling requirement for blackberries

Gambelia copeii

Number of Pages: 8Integrative BiologyGeological Science

Electric field induced charge noise in doped silicon: ionization of phosphorus donors

We report low frequency charge noise measurement on silicon substrates with different phosphorus doping densities. The measurements are performed with aluminum single electron transistors (SETs) at millikelvin temperatures where the substrates are in the insulating regime. By measuring the SET Coulomb oscillations, we find a gate voltage dependent charge noise on the more heavily doped substrate. This charge noise, which is seen to have a 1/f spectrum, is attributed to the electric field induced tunneling of electrons from their phosphorus donor potentials.Comment: 4 page, 3 figure

Probabilistic Quantum Control Via Indirect Measurement

The most basic scenario of quantum control involves the organized manipulation of pure dynamical states of the system by means of unitary transformations. Recently, Vilela Mendes and Mank'o have shown that the conditions for controllability on the state space become less restrictive if unitary control operations may be supplemented by projective measurement. The present work builds on this idea, introducing the additional element of indirect measurement to achieve a kind of remote control. The target system that is to be remotely controlled is first entangled with another identical system, called the control system. The control system is then subjected to unitary transformations plus projective measurement. As anticipated by Schrodinger, such control via entanglement is necessarily probabilistic in nature. On the other hand, under appropriate conditions the remote-control scenario offers the special advantages of robustness against decoherence and a greater repertoire of unitary transformations. Simulations carried out for a two-level system demonstrate that, with optimization of control parameters, a substantial gain in the population of reachable states can be realized.Comment: 9 pages, 2 figures; typos added, reference added, reference remove

RTP control protocol (RTCP) extended report (XR) block for independent reporting of burst/fgp discard metrics

This document defines an RTP Control Protocol (RTCP) Extended Report (XR) block that allows the reporting of burst/gap discard metrics independently of the burst/gap loss metrics for use in a range of RTP applications

Worldwide time and frequency synchronization by planned VLBI networks

Accurate baseline determinations and clock synchronization results obtained from the Quasar Patrol observations at X band with the Goldstone-Haystack baseline are presented. In addition, data from stations at Greenbank, West Virginia, and Onsala, Sweden were used. It was estimated that clock accuracy was on the order of 16 cm

Adventitious shoot propagation and cultural inputs in nursery production of a primocane-fruiting blackberry selection

Studies were conducted from January to October 2005 to determine the effect of root-cutting length on adventitious shoot yield and the management practices necessary to produce nurseryquality primocane-fruiting blackberry plants. The first portion of the study measured the average number of shoots produced from 7.6 cm- and 15.2 cm-long root cuttings of APF-44 blackberry—a primocane-fruiting genotype from the University of Arkansas breeding program. Cuttings were forced in a shallow bin containing a soilless potting medium. The average number of shoots per root cutting from 7.6 cm- and 15.2 cm- long root cuttings averaged 1.6 and 2.7 shoots per root cutting, respectively. Rooting percentage for collected shoots was nearly 100% regardless of root-cutting length source. A qualitative comparison of shoots from the two roots lengths was similar. The latter part of the study included various treatments on the rooted shoots that might affect the productivity and quality of the final product intended for nursery sales in early fall. With the aim of producing a flowering/fruiting shrub by late September, three treatments were applied: pot dimension, fertilizer rate, and shoot tipping. Fertilizer rate had the greatest impact of all treatments with the higher rate producing larger and more attractive plants. Above-normal summer/fall temperatures may explain lack of fruiting on APF-44 blackberries, but the dimension and size of some plants provided a portion of the intended aesthetic

Helmet weight simulator

A device for providing acceleration cues to the helmet of a simulator pilot is described. Pulleys are attached to both shoulders of the pilot. A cable is attached to both sides of the helmet and extends through the pulleys to a takeup reel that is controlled by a torque motor. Control signals are applied to a servo system including the torque motor, the takeup reel and a force transducer which supplies the feedback signal. In one embodiment of the invention the force transducer is in the cable and in another it is in the takeup reel

Chionactis occipitalis

Number of Pages: 12Integrative BiologyGeological Science